Messages

1

Husqvarna / VForce3 for Huskys

« on: August 20, 2014, 08:03:34 am »

I have VForce3 reed systems available for reed-equipped vintage Huskys. Easiest way to add torque and HP to your Husky. I do not lurk here often, so please contact me by email [email protected] or see my website Huskydoggg.com. Thanks!
Steve

2

Husqvarna / Re: Husky piston for 74 125, 1972 CR 400 base gasket.

« on: April 25, 2013, 01:24:34 am »

Glenn,
If you can't find 1st over, I have a new 56.5 mm Wiseco kit available.
Steve
Huskydoggg.com

3

Husqvarna / Re: 1980 390 auto gearbox shafts.....

« on: November 14, 2012, 04:07:55 pm »

KTM,
I have one NOS 1612 630 01 left. Also lots of other new and used Husky parts including parts for autos.
Steve
huskydoggg.com

4

Husqvarna / Re: 125 Husky Parts

« on: August 13, 2012, 12:47:49 pm »

Old Husky,
I have plenty of new and used parts for your 125 project. My email address is on the website. http://www.huskydoggg.com/Home.html
Steve

5

Husqvarna / Re: Be afraid - Husky CR 500 on eBay

« on: May 01, 2012, 12:54:00 pm »

Be afraid? Yes, I would be afraid to buy that bike. Just another cosmetic fix-up. Certainly not a restoration.
What does "engine and frame detailed" mean? It means rattle can paint job to make it look good on ebay to buyers thousands of miles away. No mention of important items like the bearings, seals, piston, what bore it is on, connecting rod, trans gears, etc. If you can't see the parts, they don't matter on fleabay.
Steve

6

Husqvarna / Re: husky 450

« on: April 29, 2012, 07:23:18 am »

I have what you are looking for.
http://www.huskydoggg.com/Home.html

7

Husqvarna / Re: Husky 430 bigend

« on: April 02, 2012, 12:37:40 pm »

Eurorod or NOS Husky 430 rod kits in stock at fair prices. http://www.huskydoggg.com/Home.html
Check the website for contact information, I don't check this site often.
Steve

8

Husqvarna / Re: Looking for a brake cable

« on: March 01, 2012, 12:28:59 pm »

Mike,
I have NOS rear cables 26 3/4" (680 mm) long. Not sure what year these are for.
Steve

huskydoggg.com

9

Husqvarna / Re: TC / TE 510

« on: August 18, 2011, 06:51:23 am »

Parts availability?

If anyone needs pistons, I have NOS Mahle piston kits available for the 500/510 4 strokes.
Steve

10

Husqvarna / Re: Guy in Amerika buys some Huskys

« on: July 18, 2011, 12:48:55 pm »

Sorry, I can't do anything about Canada Post. However, I can provide my very best service and very reasonable parts prices. Hopefully that offsets some of the shipping costs and delays.
I sell parts all around the world and I must say the Australians are the absolute best. You guys love your Huskys and know how to have fun. Cheers.
"Huskydoggg" Steve

11

Husqvarna / Re: Parts from England

« on: June 17, 2011, 02:31:12 pm »

On Husky forums around the world there are people reporting that they've been ripped off by HVA factory. Personally, I lost over $1000 to these crooks.

12

Husqvarna / Re: '74 WR400 output shaft end float

« on: May 27, 2011, 03:26:15 pm »

My freshly rebuilt '74 CR400 measures about 0.025" endplay. I looked at two 400 parts bikes and they are about the same.
Steve

13

Husqvarna / Re: Guy in Amerika buys some Huskys

« on: December 02, 2010, 05:01:17 am »

That "Guy in Amerika" is actually me in Canada. Bit of a surprise to find my photo posted here.
I was having trouble finding parts for a Husky rebuild until I found a retired dealer with a hoard of bikes and parts. He couldn't be bothered to look for parts, but eventually relented and said "Take it all or none!" I took it all. Forty Husqvarnas and a good stash of new parts.
Steve