1
Vinduro / Re: VTR Vinduro - Bulahdelah - March 9/10 2024
« on: April 15, 2024, 06:10:37 PM »
arrghh another one i missed, 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Suzuki / Re: Who's is this !!!!!!
« on: January 17, 2023, 11:54:13 AM »
good looker,360 the crank,& go dirt track 
3
Wanted / Re: TL250 Honda
« on: August 05, 2022, 11:24:48 AM »
what about a ball roller bearing behind the points,seen that done,slide fit on cam,just seal housing to be machined,would the XL 185/200 steel inset on the other end work as well as bushing there,btw TL head is physically smaller too than XL's circumference,
5
Spaniards (Bultaco, Ossa, Montesa etc) / Re: Super Pioneer 250 exhaust guard
« on: May 30, 2022, 09:30:13 PM »6
For Sale / TT500 engine,
« on: April 26, 2022, 09:52:13 PM »
listing for friend,76 TT500 motor,dismantled,missing clutch,$800,78 SR500 head,bare,$150,51 Matchless G9 crankcases,nos centre web,& timing case,$450 (have pictures but on my bloody phone),
wiseco 12-1 comp 88.5mm SR large inlet piston,still in box,$325
cheers mick
wiseco 12-1 comp 88.5mm SR large inlet piston,still in box,$325
cheers mick
7
General Discussion / Re: Vintage Motorcycle Scam - Beware!!
« on: October 26, 2021, 06:51:46 PM »
just amazes me it's still happening,heard of guys in vic been stung bigtime for fancy road race bikes,sells the same bike to different guys,i know of one got $20k back,still nearly that owing on another "deal",like the D's say,'if it's too good to be true,it generally is",good luck
8
Honda / Re: Honda XL250 Motosport Cam Chain Tensioner
« on: September 01, 2021, 10:46:23 AM »
probably not,just measured 20mm shorter,there's generally a good reason why the part #'s are different,
9
General Discussion / Re: Paddock bike starter any recommended
« on: May 18, 2021, 06:19:27 PM »
Pat,watch roller size,smaller dia chews/flatspot up tyres, both rollers drivings betterer too
10
General Discussion / Re: Paddock bike starter any recommended
« on: May 18, 2021, 12:03:27 PM »
depends,you want battery independance,(some tracks no power) Rosco rollers in sidinee,or mains power (gensets) kinno's rollers in Vic,used both (borrowed lol) mines home made matarbo 8" grinder,there are others,
12
Spaniards (Bultaco, Ossa, Montesa etc) / Re: H6 c/shaft sprocket
« on: March 17, 2021, 05:47:04 PM »
sorted (sorta) shimmed under sprocket on distance sleeve,
13
Spaniards (Bultaco, Ossa, Montesa etc) / H6 c/shaft sprocket
« on: March 16, 2021, 09:14:15 PM »
guys, is the c/s sprocket nut recessed to go over the spline ,one i'm working on has a plain nut,when tightened,still loose clearance againstsprocket/lock tab?? (bottoms on spline shoulder),tia
14
For Sale / NOS yamaha rods
« on: February 17, 2021, 10:22:30 PM »
2 of 2X5,(IT400,YZ400,IT425),214 (68-74 DT1,YZ 250A/360A)431-11651-00-00,43G (84-86 IT200),$80 ea + post,
15
General Discussion / Re: Husky motoplat flywheel thread size for puller.
« on: February 15, 2021, 03:26:34 PM »
Pat,ossas 27 x 1.25,small late KTM 26 x 1.5,sorry don't have huski motosplat,prob don't help,but thought i'd share with you, 
,
,