Messages

1

For Sale / Re: Yamaha it yz tt rear wheel

« on: March 14, 2020, 10:20:09 AM »

Hey Gary do you think it will fit into the DT1? The original wheel is very heavy. Is the brake on the opposite side to the sprocket?

2

Wanted / Yamaha DT1 250 rear wheel spokes

« on: February 24, 2020, 06:31:20 PM »

I'm after a few spokes (3 or 4) for my rear wheel. Could anyone help me out please?

3

Wanted / Re: IT/YZ front brake plate

« on: July 20, 2019, 08:08:10 PM »

I have a TLS / DLS in USA if would work for you.

that would be good if I could run it in pre1978 class but i doubt I can.

4

Yamaha / Wanted DT1MX STD piston ring

« on: July 20, 2019, 08:03:04 PM »

I'm after a STD DT1MX piston ring if anyone has one and I'm trying to get it before the 26 July. Happy to pay express post

5

Wanted / DT1MX piston ring STD

« on: July 20, 2019, 08:02:14 PM »

I'm after a STD DT1MX piston ring if anyone has one and I'm trying to get it before the 26 July. Happy to pay express post

6

Wanted / Re: IT/YZ front brake plate

« on: July 16, 2019, 06:08:02 PM »

Ok I've measured the drum and it looks like it would take 130mm x 22mm shoes.
IT175, 250 1980/82
YZ125 76/83
YZ250 74/81
From what I can see.
I'm adapting the wheel to suit a Husky cr250 front end.

7

Wanted / IT/YZ front brake plate

« on: July 15, 2019, 08:25:14 PM »

Wanted a IT/YZ front brake plate (possibly could use a DT one?). Cheers

8

Bike Transport / Perth to Gold Coast transport

« on: December 08, 2018, 07:07:21 PM »

Could anyone give me an idea of freight cost Perth to Gold Coast (or Brisbane) please and a decently priced transporter? Cheers

9

Tech Talk / Ohlins XJS1300 shocks revalve possible?

« on: October 24, 2018, 08:20:35 PM »

Anyone have experience re-valving road bike shocks. Of course springs will need changing but wondering if its possible to make them work?  Cheers

10

Wanted / YZ125G air filter cage wanted

« on: February 11, 2018, 12:52:59 PM »

As it says YZ125G air filter cage wanted and I believe the same as IT175, YZ100 and a few others. THANK YOU

11

Yamaha / YZ125G air filter cage wanted

« on: February 11, 2018, 12:52:33 PM »

As it says YZ125G air filter cage wanted and I believe the same as IT175, YZ100 and a few others. THANK YOU

12

Husqvarna / Re: 1982 Husky 430 minimum piston ring gap?

« on: January 17, 2018, 08:14:26 PM »

You are correct. 4 to 5 thou inch per inch of bore is fine. Use a piston to make sure ring sits square to the bike when measuring the gap. Measure 0.5 inch down from top of bore in running area of the ring. If bore is new then can measure where Husky manuals shows. If gap is too tight the bike can nip up due to ring seizure. Has happened to my Husky 500 and was easily fixed.

Thanks for the input! 

13

Husqvarna / 1982 Husky 430 minimum piston ring gap?

« on: January 15, 2018, 10:54:02 PM »

As far as Husky manuals go it only states maximum wear limit 0.8mm but doesn't show a minimum to fine the new ring to!
 
Just wondering what the minimum ring clearance should be and measured at what point in the bore (the manual states to measure at the base)?

From my understanding the diameter of the bore in this case is (86.95mm) 3.42 x 0.004 thou = 0.013692 (0.014) so approx 0.35mm sounds about right.
Anyone concur that this is a fair end gap for a new ring?

Thank you

14

Yamaha / Re: Will a twin shock Dt175 accept an early monoshock engine?

« on: January 05, 2018, 03:20:43 PM »

Thanks for the serious responses.

15

Yamaha / Will a twin shock Dt175 accept an early monoshock engine?

« on: January 03, 2018, 02:11:41 PM »

Just wondering if the later model 78, 79, 80 etc monoshock engines will fit into the earlier twin shock DT frames? Thanks